Arduino触摸代码在spark内核中不起作用
Arduino touch code is not Working in spark core
Hi我找到了使用石墨和纸张的触摸界面的Arduino代码,但该代码在Spark Core中不起作用,Arduino的代码如下
// Pin for the LED
int LEDPin = 7;
// Pin to connect to your drawing
int capSensePin = 0;
// This is how high the sensor needs to read in order
// to trigger a touch. You'll find this number
// by trial and error, or you could take readings at
// the start of the program to dynamically calculate this.
int touchedCutoff = 60;
void setup(){
Serial.begin(9600);
// Set up the LED
pinMode(LEDPin, OUTPUT);
digitalWrite(LEDPin, LOW);
}
void loop(){
// If the capacitive sensor reads above a certain threshold,
// turn on the LED
if (readCapacitivePin(capSensePin) > touchedCutoff) {
digitalWrite(LEDPin, HIGH);
}
else {
digitalWrite(LEDPin, LOW);
}
// Every 500 ms, print the value of the capacitive sensor
if ( (millis() % 500) == 0){
Serial.print("Capacitive Sensor on Pin 2 reads: ");
Serial.println(readCapacitivePin(capSensePin));
}
}
// readCapacitivePin
// Input: Arduino pin number
// Output: A number, from 0 to 17 expressing
// how much capacitance is on the pin
// When you touch the pin, or whatever you have
// attached to it, the number will get higher
// In order for this to work now,
// The pin should have a 1+Megaohm resistor pulling
// it up to +5v.
uint8_t readCapacitivePin(int pinToMeasure){
// This is how you declare a variable which
// will hold the PORT, PIN, and DDR registers
// on an AVR
volatile uint8_t* port;
volatile uint8_t* ddr;
volatile uint8_t* pin;
// Here we translate the input pin number from
// Arduino pin number to the AVR PORT, PIN, DDR,
// and which bit of those registers we care about.
byte bitmask;
if ((pinToMeasure >= 0) && (pinToMeasure <= 7)){
port = &PORTD;
ddr = &DDRD;
bitmask = 1 << pinToMeasure;
pin = &PIND;
}
if ((pinToMeasure > 7) && (pinToMeasure <= 13)){
port = &PORTB;
ddr = &DDRB;
bitmask = 1 << (pinToMeasure - 8);
pin = &PINB;
}
if ((pinToMeasure > 13) && (pinToMeasure <= 19)){
port = &PORTC;
ddr = &DDRC;
bitmask = 1 << (pinToMeasure - 13);
pin = &PINC;
}
// Discharge the pin first by setting it low and output
*port &= ~(bitmask);
*ddr |= bitmask;
delay(1);
// Make the pin an input WITHOUT the internal pull-up on
*ddr &= ~(bitmask);
// Now see how long the pin to get pulled up
int cycles = 16000;
for(int i = 0; i < cycles; i++){
if (*pin & bitmask){
cycles = i;
break;
}
}
// Discharge the pin again by setting it low and output
// It's important to leave the pins low if you want to
// be able to touch more than 1 sensor at a time - if
// the sensor is left pulled high, when you touch
// two sensors, your body will transfer the charge between
// sensors.
*port &= ~(bitmask);
*ddr |= bitmask;
return cycles;
}
Spark core抛出以下错误
包含在..中的文件中/inc/spark_wiring.h:29:0,
from ../inc/application.h:29,
from new_lwed.cpp:3:
../../core-common-lib/SPARK_Firmware_Driver/inc/config.h:12:2: warning: #warning "Defaulting to Release Build" [-Wcpp]
#warning "Defaulting to Release Build"
^
new_lwed.cpp: In function 'uint8_t readCapacitivePin(int)':
new_lwed.cpp:57:13: error: 'PORTD' was not declared in this scope
volatile uint8_t* pin;
^
new_lwed.cpp:58:12: error: 'DDRD' was not declared in this scope
// Here we translate the input pin number from
^
new_lwed.cpp:60:12: error: 'PIND' was not declared in this scope
// and which bit of those registers we care about.
^
new_lwed.cpp:63:13: error: 'PORTB' was not declared in this scope
port = &PORTD;
^
new_lwed.cpp:64:12: error: 'DDRB' was not declared in this scope
ddr = &DDRD;
^
new_lwed.cpp:66:12: error: 'PINB' was not declared in this scope
pin = &PIND;
^
new_lwed.cpp:69:13: error: 'PORTC' was not declared in this scope
port = &PORTB;
^
new_lwed.cpp:70:12: error: 'DDRC' was not declared in this scope
ddr = &DDRB;
^
new_lwed.cpp:72:12: error: 'PINC' was not declared in this scope
pin = &PINB;
^
make: *** [new_lwed.o] Error 1
Spark Core使用的CPU与Arduino不同,因此PORTC
或DDRC
等常量不可用。已移植电容式库:https://community.spark.io/t/include-capacitivesensor-library/2965/30因此您可以包含CapTouch
库并使用该示例。
相关文章:
- 我的神经网络不起作用 [XOR 问题]
- 在C++程序中输入的文本文件将不起作用,除非文本被复制和粘贴
- C++映射:具有自定义类的运算符[]不起作用(总是返回0)
- C++为什么尽管我调用了void函数,它却不起作用
- 为什么在保护模式下继承升级不起作用
- 循环在计数器中不起作用
- 在其他文件中创建类时在 c++ 项目中不起作用
- Visual studio代码重构似乎不起作用(例如,重命名符号-f2)
- 为什么二进制搜索在我的测试中不起作用
- 我的代码中有错误吗?使用BGI图形的C++代码对我不起作用
- 为什么 const std::p air<K,V>& 在 std::map 上基于范围的 for 循环不起作用?
- 带有指定长度字符* 参数的 std::regex_search 在 VS2017 中不起作用?
- Bjarne Stroustrup Book - std_lib_facilities.h - 不起作用(未知类型名称)
- 为什么简单的算术减法在"if"条件下不起作用?
- 为什么Stroustup书中的has_f不起作用
- 你能检查一下为什么在这个代码中从链接列表中删除项目不起作用吗
- 嵌套While循环不起作用(C++问题)
- C++Matching Brackets 2解决方案不起作用
- 检查 CUDA 内核中的device_vector不起作用
- Arduino触摸代码在spark内核中不起作用